Features And Specifications

THE WAVE 24/96 version 

FEATURES:

• 24 Bit 96KHz Digital to Analog Converter Board

• Totally DUAL MONO design

• Vacuum tube output stage (2 x 12AX7EH, 2 x 7044 JAN NOS USA)

• BALANCED and UNBALANCED outputs x 3

• BALANCED and UNBALANCED analog inputs x 4

• Motorized ALPS quad-attenuator volume control

• 4 x switchable digital inputs AES, SPDIF, ST, Toslink

• 1 x SPDIF digital output pass-through

• 4 x switchable ANALOG inputs balanced & unbalanced

• Tape/Processor Loop = INSERT SEND & RECEIVE on unblanced RCA jacks as standard, balanced XLR's by request

• Remote Control controls the whole faceplate

• Separate outboard Power Supply Unit

• Outboard Power Supply is factory set for 100V, 120V or 220-240VAC operation 
  for original destination country's mains voltage.

• Operating Mains Voltage: 120 to 240VAC operation changeable with power transformer re-wiring via internal switch and fuse value change. 100VAC operation changeover achieved via rewiring of power transformer PCB.

• Mains Voltage Frequency: 50~ 60Hz

• Mains Fuse Value: 1.5A SLO-BLO for 100 or 120V operation

• Mains Fuse Value: 0.75A SLO-BLO for 220V-240V operation

• Power consumption: 0.8A @ 120V = 96 watts

• Dimensions: 19" W x 5.25" H x 13" D

• Unit Weight: WAVE = 23 lbs.; PSU = 15 lbs.

• Shipping Weight: 49 lbs.
  

DIGITAL SECTION

• Burr-Brown PCM1704 D-A converters operating at 96 KHz at all times

• All inputs below 96 KHz are upsampled to 96 KHz before conversion

• The upsampled output is clocked out via a Low Phase Noise/Low Jitter
  precision crystal oscillator to eliminate any interface jitter or timing
  problems with the incoming datastream

• Multiple power supplies are used, with additional regulation and
  filtering located at all critical components

• Differential Passive LC filtering is used on the voltage output of the
  DAC PCB

• High Speed JFET Current to Voltage Conversion with differential output is
  used to drive the Passive LC Filter

• It will wash your car, clean your windows, make coffee and sound
  good all at the same time...
  

• ALL-TUBE BALANCED LINE AMPLIFIER using 2 x 12AX7 plus 2 x 7044 dual triodes

• BALANCED I/O and UNBALANCED I/O

• INPUT SENSITIVITY: 494mV (-3.9dBu) yields 1V out

• MAXIMUM INPUT LEVEL: 9.75Vrms produces 19.86V on output at 1KHz before clipping
                                                        +22dBu produces +28.18dBu on output at 1KHz before clipping

• MAXIMUM GAIN: 12 dB

• MAXIMUM OUTPUT: +30 dBu, 25 V rms (70V P-P) (+31dbu @ 1.5% THD)

•                                         +8.25 dBu digital full scale (2.0 V Rms)

• FREQUENCY RESPONSE: 20 Hz to 20 kHz +/- .5 dB
                                                    8 Hz to 45 kHz +/- 3 dB                                                

• THD+N: 0.015% 20Hz - 20KHz bandwidth

• NOISE FLOOR -88 db (20 Hz - 20 kHz) (-90 A-Weight)

• S/N 120 dB analog (96 db digital)

• L/R Volume Control Matching .2 dB (from -50 to max)
  

• 4 x DIGITAL INPUTS: AES/EBU, S/PDIF, TOSLINK, ST (AT&T GLASS)
  (Comes standard with one of each type input. These can be changed on special order upon request.)

• 1 x DIGITAL OUTPUTS: S/PDIF follows AES or SPDIF digital input selection

• 4 x Stereo ANALOG INPUTS: (standard: 2 x stereo unbalanced RCA,2 x stereo balanced XLR)

• INSERT SEND and RETURN (Tape processor loop) Available balanced XLR or Unbalanced RCA
  With analog inputs UNITY GAIN (direct connected via relays)

• 3 x Stereo ANALOG OUTPUTS: (standard: 2 x stereo unbalanced RCA, 1 x balanced XLR)
  (Output 1 is always on. You can toggle between outputs 2 and 3 or switch both on at the same time with jumper setting)

• Reference level to digital full scale: With digital -14 (CD consumer setting); With digital -20 (Pro Studio Reference Setting)

• MOTORIZED ATTENUATOR WITH FULL REMOTE CONTROL

• EXTERNAL POWER SUPPLY

• DIGITAL PHASE / POLARITY SWITCH,

• INSERT FOR TAPE MONITOR, PROCESSOR LOOP, ETC.

• MANUAL MUTE, WARM-UP MUTE & STANDBY MODES.

• "Manley Blue" anodized 3/8" thick by 19" FRONT PANEL, 18 BLUE LEDS

• UPGRADEABLE DIGITAL BOARD

• MANY CUSTOM OPTIONS AVAILABLE INCLUDING:
  ANY COMBINATIONS OF BALANCED AND UNBALANCED I/O, OR ANY COMBINATION OF DIGITAL INPUT TYPES. (Expect extra NRE charges for anything involving custom silk-screening of faceplate)
  INSERT MOD FOR SURROUND PROCESSORS (RETURN POST LINE AMP)

REMOTE CONTROL RANGE MEASUREMENTS:  

If the remote is closer than 9 feet, the maximum angle response is around 60 to 75 degrees which is the counter sink angle of the receiver's hole in the front panel. Measurements done with new set of batteries.  

• Distance of 9-10 ft, the maximum angle is 65-75 degrees.
• Distance of 12 ft, the maximum angle is 60 degrees.
• Distance of 13 ft, the maximum angle is 45-55 degrees.
• Distance of 16 ft, the maximum angle is 45 degrees.
• Distance of 20 ft, the maximum angle is 25-35 degrees.
• Distance of 25-27 ft, the maximum angle is 0-15 degrees. This is the maximum distance-angle the remote will do.