Enthusiastic users rave! Reviews Great Minds Think Alike Massive FAQ More Mastering Info Worldwide Dealers   Mic Pres | Compressor Limiters | EQs | Combo Units | Mics | DIs | Mastering | Starbird Boom | Amps | Mixers

Manley Mastering Version Massive Passive EQ  Features And Specifications | Massive FAQ | Suggested Retail Price | Massive Massive Pix    Users Rave | Massive Passive Owner's Manual PDF | Mastering Version Massive Passive session template

Yes finally! Manley Mastering Version Massive Passive Stereo Tube EQ WE FINALLY CAME UP WITH A CLEVER WAY TO PULL THIS OFF... ...WITHOUT breaking your bank account thanks to these interesting mechanically detented knobs for the GAIN and BANDWIDTH controls! These ensure repeatability which is what everyone wanted but without the incredible cost and space problems tons of Grayhill switches would have caused.  Some notes pertinent to the Mastering Version: The Massive Passive is a passive design and not a "true parametric". A true parametric implies non-interacting controls. In the Massive Passive, the "GAIN" and "BANDWIDTH" controls DO interact (on purpose). We cannot create a "GAIN" switch that is set up for "consistent" 1/2 dB steps. When you change the "BANDWIDTH" the step size must and will change. On the regular version, you get a full 20dB boost or cut only when: the bandwidth is fully clockwise (narrow) in bell mode or fully counter-clockwise in shelf mode. Here on the Mastering Version, this maximum boost or cut is 11dB. Conversely at the widest bell, the maximum boost or cut is 6dB and the narrowest shelf maxes out at 12 dB. A similar situation is also true for the bandwidth detents. So in this new Mastering Version, do not expect a certain dB change per step as it will vary according to where the bandwidth is set. But whatever the step sizes are, they will be repeatably 16 steps. The FREQUENCY select is already detented as it is and always has been a Grayhill switch. It also interacts in shelf mode. On a similar note, the Massive Passive is a "parallel design" and not the conventional "series design". This means the bands interact with each other too. It is possible, to set a band to boost 20 dB but if another band is boosting near or at that frequency, very little will happen. On a conventional EQ the two bands "add" and you would be boosting 40 dB into clipping. Because the bands interact, predictable step sizes are unrealistic, however, with the Mastering Version, you will be able to repeat settings (if you log them of course). The price paid for interacting bands, is a better sounding EQ and bizarre looking settings (on purpose). Unlike virtually every other EQ, the Massive Passive allows much more EQ without sounding "processed". Where 5 or 6 dB is about all one could attempt with other EQs in mastering, the Massivo amazes engineers with how much EQ they can do and get more "natural" results at the same time. We could have squeezed 11 position Grayhill switches in the modules if we had wanted 1/2 dB steps but then the maximum range would have become only 5.5 dB. Remembering what we stated above, the minimum range would then become about 1.5 dB with approximately 0.2 dB steps. This approach would have essentially thrown away most of the useful range the unit is capable of. Going with these special mechanically detented knobs which use the same pots underneath that the normal Massivo uses, we get nearly all the range of the normal version, but with the repeatability of the detents. We have also custom tailored the FILTERS in the Mastering Version specifically for Mastering purposes, moving them lower and higher than the normal version, with mastering engineers specifically in mind. If you are looking for drastic effects (like telephone sounds) then get the normal version. These filters are really geared for mastering engineers. Additionally, the Master Gain Trim controls in the Mastering Version are true 11 position 1/2 dB stepped Grayhill switches set up for a range between -2.5 to +2.5 dB of master gain trim. This allows more confidence in left/right matching and calibration.  The best advice is, before you decide, or even form an opinion about whether to go with a normal or mastering version Massivo, is to use a regular Massive Passive for a session or two in your own room. We have seen in the past that the only engineers who have asked about a mastering version had yet to try the Massive. Using your previous extensive and intensive experience with other EQs may be a mistake, especially if you expect the Massive Passive to be roughly similar to them. It isn't. Please, try it first, then decide. More info on the regular version Massivo page The Filters - 5 frequencies Hi Pass and bypass, PLUS 5 frequencies Lo Pass with bypass. High Pass Filters = 12, 16, 23, 30, 39Hz, OFF Low Pass Filters = 15K, 20K, 27K, 40K, 52KHz, OFF The new filters are somewhat better tuned specifically for mastering. (They are flatter until the knee). As with the standard version the slopes are typically 18dB per octave, on these mastering filters except for the highest (52K) at 30 dB/octave. ------------------------------------------------------------------------>  Parametric Frequencies (same as normal Massivo): LOW - 22, 33, 47, 68, 100, 150, 220, 330, 470, 680, 1K LM - 82, 120, 180, 270, 390, 560, 820, 1K2, 1K8, 2K7, 3K9 HM - 220, 330, 470, 680, 1K, 1K5, 2K2, 3K3, 4K7, 6K8, 10K HI - 560, 820, 1K2, 1K8, 2K7, 3K9, 5K6, 8K2, 12K, 18K, 27K For a truly massive look at the Massive Passive EQ Click Here Please be patient, loading takes time!

nominee

Rear View:

Click for bigger view

Click to enlarge.

More info on the regular version Massivo page

Massive FAQ

Great Minds Think Alike